The CPU module and most other subsystems connect to the motherboard. Without proper grounding, an electrostatic discharge can damage the notebook and its components.
NOTE: Reassembly steps are the reverse of the removal steps. Reassembly notes are included at the end of each section below. Symbols like these are displayed throughout this chapter to show approximate full-size screw outlines. You can use these to verify the sizes of screws before you install them. Installing a wrong-size screw can damage the notebook. The symbol at the left represents an M2. Using the wrong type of module prevents the notebook from booting.
Unplug the AC adapter, if present, and then remove the battery. On the bottom of the notebook, loosen the captive screws holding the SDRAM door, and then remove the door. On the bottom of the notebook, loosen the captive screws holding the Mini PCI door, and then remove the door. Damaged cables or connectors can degrade notebook performance. Disconnect the 2 antenna cables from the Mini PCI card. Carefully pull the Mini PCI card out of the connector.
The procedure for removing the Mini PCI door and card is the same for. On the bottom of the notebook, remove the hard disk drive rubber screw plugs and M2. The number of plugs and screws varies by model. Carefully pull the hard disk drive out of the notebook. Remove the four M3. Remove the connector bar from the hard disk drive. This process can take up to 15 minutes to complete.
For more information about recovering the factory software installation, see the readme. Connect the AC adapter to the notebook. If the notebook is turned off, use a pin or straightened paper clip to press the release switch on the drive door to open it.
Turn on or restart the notebook. When the HP logo appears, press esc to display the Boot menu. When the dialog box appears, follow the displayed instructions. If prompted, accept the recommended partition size. To create the Utility partition without installing the factory software, select Advanced, and then select not to install the operating system.
If the hard disk is partitioned into several logical drives, you can install the factory software on. When the operating system has been installed and while Windows is running, replace the. Follow the on-screen instructions for installing the drivers. After the drivers have been installed, the application software may be installed. Remove the two M2. Carefully insert a flat-blade screwdriver blade under the keyboard cover near the right end, then near the center, then near the left end, and then gently lift up the center of the cover.
Gently pry up the hinge covers if needed, being careful not to damage the plastics or wireless antenna underneath. Damaging either antenna PCA can degrade notebook performance. If necessary, while holding the center of the cover, carefully insert the flat-blade screwdriver under the right side of the display assembly hinge, gently pry up, and then lift the cover out.
This procedure might need to be repeated on the left side of display assembly hinge to completely remove the cover. Insert the tabs on the leftand right-center of the panel into the mating slots under the keyboard, and then press the panel into place. Compaq Presario and Series notebooks. Remove the keyboard cover page Remove the M2. Disconnect the 4-wire cable from the switchboard PCA. Remove the four M2. Lift up on the keyboard at the switchboard PCA end, and then pull it toward the display assembly to release the tabs from the top case.
Turn the keyboard over, and then disconnect the motherboard cable. Excessive flexing can damage the keyboard cable connectors. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password?
Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. HP shall not be liable for technical or editorial errors or omissions contained herein. Figures Figure One-touch buttons 3. Keyboard status lights 4. Power button, turns the notebook on and off 5. Touch pad, scroll pad, Select buttons, plus on-off button 6.
Microphone option not available 8. Battery AC adapter jack Parallel port LPT1 , use this port for a parallel printer or other parallel device Serial port COM1 , use this port for a serial mouse, modem, printer, or other serial device External monitor port Audio jacks left to right , external microphone and audio out headphones Service Manual Product Information Main status lights left to right , power mode, hard disk activity, and battery 7.
Audio jacks left to right : external microphone and audio out headphones External monitor port. Kensington lock cable slot security connector Sign Up or Sign In.
Resources and networking for those who conduct or interpret meta-analyses related to any phenomenon that is gauged in multiple studies. Model: Compaq Presario Manufacture : HP Compatibility: Windows XP Install all of the drivers given and install according to the instruction given, for the last download which is the DVD firmware, it is optional and you can choose weather to install it or not. Electronics service manual exchange : schematics,datasheets,diagrams,repairs,schema,service manuals,eeprom bins,pcb as well as service mode entry, make to model and chassis correspondence and more.
The closest I can come is the removal procedure on page of the Service Manual. When purchasing the manual, please note that the Payment will be made to TrinixSoft. This is because TrinixSoft. Once the payment is completed, you will receive an email with link to the manual with in a couple of minutes from the time of purchase.
Make sure your SPAM filter is setup to allow emails from the e-servicemanuals. If it isn't, you may have trouble receiving the manual.
0コメント